In Stock Hot Product
MSTBT 2,5 HC/ 3-STP BU TP:L2 OUT
MSTBT 2,5 HC/ 3-STP BU TP:L2 OUT 1451378 PHOENIX CONTACT Connector for printed circuit board, nominal sectio..
$2.63
USD
3845 in stock
Key Specifications
:
• WARNING: Only operate products in perfect condition. Regularly check the products for damage. Immediately take out defective products. Replace the damaged products. The item cannot be repaired.
Link:
Screw connection with cage
Step:
5 mm
note:
Complies with WEEE/RoHS, no thread-like materials according to IEC 60068-2-82/JEDEC JESD 201
Supplier Information
Products: 0
Usually ships within 2-3 business days
Quality Guaranteed
Fast Shipping
Technical Support
Technical Specifications
| Parameter | Value |
|---|---|
| • WARNING: Only operate products in perfect condition. Regularly check the products for damage. Immediately take out defective products. Replace the damaged products. The item cannot be repaired. | |
| Link | Screw connection with cage |
| Step | 5 mm |
| note | Complies with WEEE/RoHS, no thread-like materials according to IEC 60068-2-82/JEDEC JESD 201 |
| type | Standard |
| Result | Test passed |
| Amplitude | 0.35 mm (10 Hz ... 60.1 Hz) |
| Frequency | 10 - 150 - 10 Hz |
| Width [w] | 15 mm |
| Height [h] | 15 mm |
| Length [l] | 18.1 mm |
| Sweep Speed | 1 octave/min |
| Color (Case) | Blue (5015) |
| No. of poles | 3 |
| Product Line | COMBICON Connectors M |
| Product Type | Printed circuit board connector |
| Clamping Type | absent |
| Fixing flange | absent |
| Number of rows | 1 |
| Product Family | MSTBT 2.5 HC/.. -STP |
| Surface Finish | Hot-dip galvanizing |
| Connector system | COMBICON MSTB 2.5 HC |
| Contact Material | Cu Alloy |
| Fixed AC voltage | 3.1 kV |
| Mass Resistivity | 1.2 mΩ |
| Number of cycles | 25 |
| Rated Current IN | 16 A |
| Rated voltage UN | 250 V |
| Tightening torque | 0.5 Nm ... 0.6 Nm |
| Manoeuvring cycles | 25 |
| Note for Operation | According to DIN EN 61984, COMBICON connectors are switchable powerless (COC) connectors. For intended use, they must not be plugged in or disconnected when they are still energized or under load. |
| Test Specification | DIN EN 60999-1 (VDE 0609-1):2000-12 |
| Degree of pollution | 3 |
| Dimensioned Drawing | |
| Insulation material | PA |
| Mass Resistivity R1 | 1.2 mΩ |
| Mass Resistivity R2 | 1.23 mΩ |
| Safety instructions | WARNING: Connectors must not be connected or disconnected under load. Failure to comply with it and use it in accordance with the rules may result in damage to persons and/or property. |
| Nominal cross-section | 2.5 mm² |
| Sizing voltage (II/2) | 630 V |
| Number of poles tested | 4 |
| Sizing voltage (III/2) | 320 V |
| Sizing voltage (III/3) | 250 V |
| Test duration per axle | 2.5 h |
| Contact Connection Type | female |
| Stress due to corrosion | 1.0 dm3KNOW2on 300 dm3/40 °C/3 cycles |
| Insulation Material Group | The |
| CTI according to IEC 60112 | 600 |
| Conductor cross-section AWG | 24 ... 12 |
| Rated Impulse Voltage (II/2) | 4 kV |
| Buffer Gauge a x b / diameter | 2.8 mm x 2.0 mm / 2.4 mm |
| Minimum creepage value (II/2) | 3.2 mm |
| Rated impulse voltage (III/2) | 4 kV |
| Rated impulse voltage (III/3) | 4 kV |
| Rigid conductor cross-section | 0.2 mm² ... 2.5 mm² |
| Sizing Impulse Voltage (II/2) | 4 kV |
| Ambient temperature (mounting) | -5 °C ... 100 °C |
| Minimum creepage value (III/2) | 1.6 mm |
| Minimum creepage value (III/3) | 3.2 mm |
| Rated Isolation Voltage (II/2) | 630 V |
| Sizing Impulse Voltage (III/2) | 4 kV |
| Sizing impulse voltage (III/3) | 4 kV |
| Tensile force per pole approx. | 7 N |
| Ambient temperature (operating) | -40 °C ... 105 °C (depending on the derating curve) |
| Rated Isolation Voltage (III/2) | 320 V |
| Flexible conductor cross-section | 0.2 mm² ... 2.5 mm² |
| Insertion force per pole approx. | 11 N |
| Rated insulation voltage (III/3) | 250 V |
| Stress due to the effect of heat | 100 °C/168 h |
| Conductor/board connection direction | 0 ° |
| Length of the section to be stripped | 7 mm |
| Ambient temperature (storage/transport) | -40 °C ... 55 °C |
| Combustibility class according to UL 94 | V0 |
| Vertical impulse tension above sea level | 4.8 kV |
| Relative humidity (transport and storage) | 30 % ... 70 % |
| Metal surface contact zone (surface layer) | Tin (4 - 8 μm Sn) |
| 2 conductors of identical cross-section, rigid | 0.2 mm² ... 1 mm² |
| Insulation Resistance Between Contiguous Poles | > 21 TΩ |
| Metal Surface, Connection Point (Surface Layer) | Tin (4 - 8 μm Sn) |
| 2 conductors of identical flexible cross-section | 0.2 mm² ... 1.5 mm² |
| Minimum creepage value - inhomogeneous range (II/2) | 3 mm |
| Minimum creepage value - inhomogeneous range (III/2) | 3 mm |
| Minimum clearance value - inhomogeneous range (III/3) | 3 mm |
| Resistance to surface currents (DIN EN 60112 (VDE 0303-11)) | CTI 600 |
| Brinell hardness test temperature according to EN 60695-10-2 | 125 °C |
| GWIT filament ignition temperature according to EN 60695-2-13 | 775 |
| Flammability index of GWFI filament according to EN 60695-2-12 | 850 |
| Flexible conductor cross-section with mounted lug and plastic collar | 0.25 mm² ... 2.5 mm² |
| Flexible conductor cross-section with cable lug without plastic collar | 0.25 mm² ... 2.5 mm² |
| Conductor cross-section/conductor type/tensile force nominal value/actual value | 0.2 mm² / rigid / > 10 N |
| 2 conductors of the same flexible cross-section with ferrule without plastic collar | 0.25 mm² ... 1 mm² |
| 2 conductors of identical cross-section flexible with TWIN ferrule with plastic collar | 0.5 mm² ... 1.5 mm² |
Product Description
Printed circuit board connector
Key Features
- Industrial grade quality
- RoHS compliant
- CE certified
- 1-year warranty
Product Documents
Datasheet
Technical specifications and performance data
User Manual
Installation and operation guide
